|
|
|||||||||||||||||||||||||||
Background
The Kit Trumpeter's latest addition to its catalog of 1/35 train stock comes in a large, sturdy box containing eight separately bagged trees of light-gray plastic parts and a separate compartment for the single piece upper section of the rolling stock. The parts are crisp and flash-free, and effort has been made to restrict the many ejector pin marks to areas that are not visible from the outside. The flak gun platform and the protective armor around the car-coupling hardware are the only areas that will need these marks cleaned up. The plastic is soft and sands easily.
There is no interior provided, but there is a lot of wide-open-space to scratch-build one – the car is basically a hollow show-box! Three sets of double doors can be assembled in the open position to expose the interior if desired.
The Build I started with the road bed. This is a multi-step (yet separate) process so I kept coming back to it as I built up the rest of the kit. Trumpeter gives you an option to add this track to another set of track so the first thing I had to do was to remove a section of one of the end pieces so the base would be the right length for just this kit. There are deep scribed marks on the inside of each side for doing this and after 20 seconds with my razor saw I was done. The rest of the base is snapped together and then glued. These parts are very large and I found I had to glue and clamp each section individually to minimize the seams – which are significant when viewed up close. With more time I would have sanded and filled the seams on the base, but I felt they looked ok after painting them black. The seams on the roadbed itself disappeared after painting and weathering. The four wheel trucks went together without a problem. There isn’t much detail provided here, but 99% of it is out of sight anyway. Trumpeter ‘Wiggle Fit’ Trumpeter kits seem to always have a peculiar fit issue, at least in my experience. The parts fit together – that’s not the problem. The problem is that they have wiggle-room after being attached – just enough so that things may not line up if you just let them be after gluing. You have to fiddle with everything until the glue has had a chance to set up a little. I clean and bag all the parts of a model (by step) before I start assembly, and that approach really pays off for kits like this. A prime example of the problem is encountered in Step 3, when the two wheel trucks are assembled. There are 44 parts in all, 22 for each truck. If any one of those 22 parts is glued fast before you have all them together, you may end up with a crooked set of wheels, or a set of wheels that do not sit properly on the track. I encountered this with the previous Geschutzwagen build so I was ready for it this time. If you use slow-drying glue, such as Testors Liquid Cement, you should be fine.
Also, the hinges are molded to have a ‘wide’ side and a ‘narrow’ side – they can easily be installed upside down. Easily I say! A little pre-fitting will help to insure the actual hinge falls along the edge of the door and the superstructure correctly. Flakvierling and Platform Assembly The platform for the Flakvierling 38 consists of six parts, a base and five wall sections. These wall sections have prominent ejector pin marks that will have to be filled and sanded if you wish to make your build competitive.
The assembly of the quad 2cm gun consists of 79 plastic and 48 photo-etch parts. I easily spent more time on this assembly then the whole rest of the kit combined. While most of the parts came together well, there were several exceptions.
Second: The main guns (the very first step in the instructions!) had no positive attachment points – in fact, there are two posts that stick out preventing even a sloppy blob of glue to suffice. I did not want to remove the posts as they look like they were deliberate and removing them might have caused some other fit problem down the line. Consequently, it seemed like every time I applied any pressure to the assembly whatsoever, one or more of the guns popped off and had to be re-attached. Much later, after putting together the entire assembly, did I learn that I should have just filed these posts off to begin with. I’m not sure where Trumpeter was going with this design. Third: The drawings for attaching many of the photo-etch pieces that made up the four main parts of the gun shield were ambiguous at best. I ended up attaching some parts simply based on where I thought they looked best.
Finally: The three-piece seats (3 of them) must be reworked in order to fit properly. They are engineered about 75% of the way; the rest is up to the builder I guess. There’s not even a ‘wiggle-fit’ here. Fortunately, with a little effort, I think the final result looks pretty good when sitting proud on the top of the model where all eyes will be focused.
The 105mm Cupola Assembly In Step 9, as with the Flakvierling above, the keyword is patience. Go slowly here – the 10-sided cupola is built up using a base containing five sides, with five additional sides attached to fill the gaps. The final assembly needs to be relatively strong because there are many items that need to be attached to it. A little filling and sanding cleaned up the rough edges left behind. The main 10cm armament is attached via a single three-sided slot – a very weak arrangement as the gun (in my kit) kept slipping out of the slot as soon as I set it in. I decided to guess at which elevation would look the best and used a whole lot of Testor’s (black bottle) liquid glue to secure it to the base. I did not want that gun coming loose and rattling around after I glued the cupola to the base. I had to carefully fiddle with the gun elevation and horizontal angle for 15 minutes before it stayed where I wanted it to. Super glue would not have been practical here due to the ubiquitous wiggle-fit described above.
The bumpers and walkway housings I decided to assemble and attach both bumper panel assemblies on the lower car base before attempting to mate the upper and lower halves of the train car. I did this to give the two halves more surface area to use for gluing. After the panels were dry I put the whole base on a lazy susan so I could apply liquid cement around the entire car without handling it too much. After the upper and lower halves were completely dry I tackled the armored covers to the train couplings in Steps 12 and 13. I ran into trouble with these in the Geschutzwagen build and the design hasn’t changed with this kit. Ignore the part number call-outs and use the images instead. How the small tabs on the vertical plates are supposed to line up with the horizontal plate, and how all three are supposed to fit to the bumper plates is ambiguous. I decided to glue the horizontal plate on the train car first, let it dry, and then glue the vertical plates on, one at a time. One side of the train car is slightly beveled so make sure to test each vertical plate before gluing. As with everything else, there is no ‘positive fit’ anywhere. You have to nurse each piece to make sure it lines up true. This could also have been designed better. Painting and Finish
The rolling stock: I usually assemble armor kits completely before painting, leaving only the machine guns and antenna off until the end. Even though the Geschützwagon appears to be one big box, it has many protruding edges and handles, etc., so in order to wash the completed model I placed it in a small plastic tub and covered it with a heavy layer of ‘No Touch Tire Care’ product used for cleaning car tires. Once the foam had completely dissolved I thoroughly rinsed the car with warm water and set it aside to dry for a couple days. Still, even after this tried-and-true approach, I noticed a chemical sheen on several areas on the car. I decided to coat the whole thing with a layer of Future acrylic to make sure I had a consistent surface to start with. I gave the whole model a base coat of Tamiya NATO Black, thinned 50/50 with Gunze Self Leveling Thinner. I like using this as a base coat for armor because it gives me the color of Floquil Grimy Black but is less fussy to use and feels a little more ‘grimy and grainy’ to me. I was in a quandary regarding the camouflage of the main car itself. The instructions would have me paint the car using late war colors (Panzer Yellow, red-brown and dark green). I wondered, however, how often whole trains were actually camouflaged in such a manner. In the movie ‘The Train’, starring Burt Lancaster, the Geschutzwagen I built prior to this kit was prominently featured – and it wore a dull, war-like beaten-up gray scheme. Doing a little research I found that these trains were sometimes camouflaged, sometimes left in plain Panzer yellow, sometimes left as bare metal with some sort of primer on it. There are also pictures of whitewashed trains used during winter campaigns. When I think of trains, especially late-war trains, I think gray and dirty, so that’s the scheme I decided to use on this kit as well.
The Flakvierling 38: I painted the two larger photo-etch shields and the remaining gun assembly separately. I first gave everything a primer coat of Gunze Mr. Surfacer 1200. I followed this with a base coat of Tamiya NATO Black. I used a primer coat to give the photo-etch a bite for the Tamiya paint to hold on to. Both of these layers are very thin and (I feel) did not detract from the look of all the delicate parts making up the gun. I followed this by carefully airbrushing the Model Master Intermediate Blue, following it with a dusting of Model Master Light Grey, just like the train car. I tried my best to avoid the actual guns and ammunition cases – leaving them NATO Black. I then gave everything a coat of Future to prepare the surface for washes and filters.
Decals The decals supplied with the kit were thin and in-register. There are 30 markings altogether, 2 Balkan crosses and 28 white stencils. Even though the decals are thin they are STRONG, which is good thing because the glue is also strong – make sure you get the decals pretty well were they need to go the first time because they are difficult to move one they are down. I coated the areas to receive decals with Future before and after applying the decals. I used the Microscale system (Micro Sol and Micro Set) without any problems. Once the decals were dry, I gave the model a thorough coat of Testors Dullcoat to even everything out. The build took me about 15 hours to complete, most of the time spent on the Flakvierling 38. Conclusion This was an unusual project, no doubt. I grew up with an HO-scale train set, so the train-guy in me provided the motivation to do a full-build article rather than just an in-the-box write up. When I attend model shows I always like the big, bold dioramas in 1/35th scale encompassing many kits and figures, and trains fit into such a scenario like a hand in a glove. I applaud Trumpeter for coming out with this kit and I hope to see some similar releases in the future. I felt that the problems encountered when building the Flakvierling 38, attaching the doors and other parts such as the walkway housings were minor annoyances and offset by the brilliant design of the roadbed and track. Overall, this kit provided me with an opportunity to knock out something quick and enjoyable. I would recommend this kit to modelers with some experience in solving problems due to the fit issues. That said, however, the kit builds into a very nice and unique representation. I'd like to thank Steven’s International for providing the review sample. |
Digg
this story!
|
||||||||||||||||||||||||||
